Buster Xcalibur, like its predecessors, is an Attack Type Energy Layer based on the legendary sw0rd Excalibur that features a large sw0rd running down the length of the layer, the end of which protrudes from the bottom which acts as the primary point of contact. Unlike previous Xcalibur Layers such as Sieg Xcalibur and Xeno Xcalibur, Buster Xcalibur’s contact point is very pronounced which creates high Knock-Out and Burst Attack potential, but also creates high recoil. As part of the Cho-Z Layer System, Buster Xcalibur features metal in its design. in this case, the sw0rd is made of metal, akin to its predecessor Sieg Xcalibur. However the tip of the sw0rd is covered in plastic, to reduce the possibility of breaking the opponent's Layer. Buster Xcalibur also features a gimmick, the sw0rd can extend further from the rest of the Layer to create a \"Buster Mode\".

The inclusion of metal increases the weight of the Layer, granting higher inertia that increases both Knock-Out and Burst Attack as well as increasing the Layer's Burst resistance as the high inertia resists teeth skipping, a property that compliments the tall teeth of the Japanese release. However the asymmetrical design of the metal sw0rd means that this Layer is incredibly unbalanced, a trait that drains the Stamina of Combinations and can break a Combination's banking pattern. Furthermore, the shape of the Layer makes it a very poor choice for Opposite Spin matchups. Finally, Buster Xcalibur is so unbalanced that it cannot be used with unbalanced Discs such as 1, else it will lose Stamina too quickly to be effective in battle. Due to the nature of the gimmick, the recoil of Buster Xcalibur can be adjusted by either retracting or extending the sw0rd. However, the locking mechanism for the gimmick is weak, meaning that Buster Xcalibur is prone to switching to \"Buster Mode\" midway through the battle even if it was set to \"Normal Mode\". Like other Cho-Z Layers and previous Xcalibur Layers, Buster Xcalibur is unbalanced which increases Burst risk and drains Stamina. 

#Takara #Tomy #Beyblade #Burst #Cho-Z #B-120 #Starter #Buster #Xcalibur

Cho-Z Valkyrie.Z.EV  is an Attack Type Energy Layer, the center features a feathered, armored face facing forward, akin to its predecessor Winning Valkyrie, meant to represent the Layer's namesake; Odin's handmaidens of Norse mythology, albeit changed to match the anime's rendition; an armored knight. Like its predecessors, Cho-Z Valkyrie features three large wings as the primary points of contact, granting the Layer high Knock-Out and Burst Attack potential. As part of the Cho-Z Layer System, Cho-Z Valkyrie features metal in its design; in this case, concentrated behind each wing and in the center. However, Cho-Z Valkyriefeatures less metal than most other Cho-Z Layers and most of its weight comes from its size. Cho-Z Valkyrie also features a gimmick; the Layer features an anti-Bursting mechanism called the "Cho-Z Awakening System".

At high spin velocity, the centrifugal force activates a bistable mechanism, revealing red sub-wings called the "Cho-Z Wings" and in turn extending a Burst-stopping tab located in the left groove meant to fit the prongs of the Disc. This Burst-stopper then obstructs the Disc from moving during impact, preventing the loss of the last click and preventing the Cho-Z Valkyrie combination from Bursting. Due to the bistable mechanism, the wings and tab do not retract when spin speeds are low and must be manually pushed in after every match, the mechanism also allows the gimmick to work as intended.

Because of Cho-Z Valkyrie's triangular design, only the upper-left wing will move the tab with the other two being purely aesthetic. However, due to the bistable mechanism, Cho-Z Valkyrie requires rather extreme spin speeds for the gimmick to activate which may be difficult for younger bladers.

The Layer's size and the inclusion of metal makes Cho-Z Valkyrie heavier than most SwitchStrike/God Layers and improves Attack Potential by increasing the weight of the Layer, granting higher inertia that increases both KO and Burst Attack as well as increasing the Layer's Burst resistance as the high inertia resists teeth skipping, a property that compliments the tall teeth of the Takara Tomy release of Cho-Z Valkyrie. Due to these factors and the shape of the blades, Cho-Z Valkyrie performs well in Attack Combinations. However, the wings of Cho-Z Valkyrie show greater Attack potential when the "Cho-Z Wings" are not active as they cover up a more acute point of contact and when the "Cho-Z Wings" are active, the new point of contact is much more obtuse, reducing recoil. As such, Cho-Z Valkyrie almost requires the use of the three pointed Zenith Disc to concentrate weight at the points of contact to be effective with the gimmick activated.

Unlike previous Cho-Z Layers and like other Layers with the "Cho-Z" and "Turbo" prefixes, Cho-Z Valkyrie and Turbo Valtryek V3 are both incompatible with a Level Chip.

 Beyblade Burst Cho-Z B-124 Long Bey Launcher Set support left spin Beyblade only and provide super sharp shoot!

This set contains 1 x Geist Fafnir enhanced part. 

Content:

- Long BeyLauncher L

- Carabiner Grip

- Weight Damper

- Proof